Home

I2C

CRIUS Pixhawk I2C Splitter Expand Module For Pix APM Flight Controller

CRIUS Pixhawk I2C Splitter Expand Module For Pix APM Flight Controller

CRIUS Pixhawk I2C Splitter Expand Module For Pix APM Flight Controller Description: Brand Name: CRIUS Tool Supplies: Cutting Material: Composite Material RC Parts & Accs: Connectors/Wiring Model Number: Pixhawk I2C Size: 12x30x6mm Note:if the existence of the cable portion of red and black lines received the wrong location, please ignore, because it does not affect the use, but the color sequence is incorrect, you can swap your own if necessary. Features: Pixhawk/APM flight control only one I2C interface, such as the need to connect more than one I2C peripheral, you can use the line board; Pixhawk - I2C points line board with five completely parallel vertical 1.25 4 a socket, convenient connection in the form of 1 drag 4 four I2C peripherals, for example, at the same time use the external compass and RGB modules. I2C line board and Pixhawk flight control the appearance of the connection (please note that this price includes only the I2C line board and cable) Package includes: 1x Pixhawk-I2C module 1x 4P Cable 60mm

Toys/Games/Electronic

CRIUS Pixhawk I2C Splitter Expand Module For Pix APM Flight Controller

RTC v1.1 DS1307 Real Time Clock Module w/ I2C - Blue

RTC v1.1 DS1307 Real Time Clock Module w/ I2C - Blue

The module is based on DS1307 high precision real time clock module; Through I2C interface to communicate with singlechip, can read year, month, day, week, time, minute, second; Car read until 2100 year; Control interface is I2C; Recommended power: DC 5V; The address of the module is 0x68; Control interface level is 5V or 3.3V; 4-M2 screw hole, easy to install. Specification Power voltage VCC: 4.5~5.5V; Battery voltage: 2.0~3.5V; High level input: 2.1~VCC + 0.3V; Low level input: -0.3~+0.8V; Control interface: 4-pin (GND, VCC, SDA, SCL), GND for ground wire, VCC for power source, SDA for I2C interface data cable, SCL for I2C interface clock cable; Real time IC: DS1307Z; Independent timing: through I2C interface communicate with MCU; Battery: CR1220; Installed hole: 4-M2 screw hole, diameter hole: 2.2mm, easy to install
 
GeneralBrandOPEN-SMARTModelRTC v1.1Quantity1 pieceForm ColorBlue + SilveryMaterialPCBSpecificationChipsetDS1307English Manual / SpecNoDownload Link http://pan.baidu.com/share/link?shareid=1570527979&uk=1966479381Other FeaturesOther FeaturesPower voltage VCC: 4.5~5.5V; Battery voltage: 2.0~3.5V; High level input: 2.1~VCC + 0.3V; Low level input: -0.3~+0.8V; Control interface: 4-pin (GND, VCC, SDA, SCL), GND for ground wire, VCC for power source, SDA for I2C interface data cable, SCL for I2C interface clock cable; Real time IC: DS1307Z; Independent timing: through I2C interface communicate with MCU; Battery: CR1220; Installed hole: 4-M2 screw hole, diameter hole: 2.2mm, easy

Electronics/Wireless

RTC v1.1 DS1307 Real Time Clock Module w/ I2C - Blue

IIC I2C TWI SP Serial Interface Port Module 5V 1602LCD Adapter For Arduino

IIC I2C TWI SP Serial Interface Port Module 5V 1602LCD Adapter For Arduino

Description: This is another great IIC/I2C/TWI/SPI Serial Interface. As the pin resources of Arduino controller is limited, your project may be not able to use normal LCD shield after connected with a certain quantity of sensors or SD card. However, with this I2C interface module, you will be able to realize data display via only 2 wires. If you already has I2C devices in your project, this LCD module actually cost no more resources at all. It is fantastic for Arduino based project. I2C Address: 0X20~0X27 (the original address is 0X20,you can change it yourself) the backlight and contrast is adjusted by potentiometer Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated cable I2C Address: 0x27 (I2C Address: 0X20~0X27 (the original address is 0X27,you can change it yourself) Specification: Compatible for 1602 LCD Supply voltage: 5V Weight: 5g Size: 5.5x2.3x1.4cm Package included: 1 x IIC/I2C/TWI/SPI serial interface module port

Electronics/Audio

IIC I2C TWI SP Serial Interface Port Module 5V 1602LCD Adapter For Arduino

5Pcs IIC/I2C/TWI/SPI Serial Port Module 5V 1602LCD Display For Arduino

5Pcs IIC/I2C/TWI/SPI Serial Port Module 5V 1602LCD Display For Arduino

Description: This is another great IIC/I2C/TWI/SPI Serial Interface. As the pin resources of Arduino controller is limited, your project may be not able to use normal LCD shield after connected with a certain quantity of sensors or SD card. However, with this I2C interface module, you will be able to realize data display via only 2 wires. If you already has I2C devices in your project, this LCD module actually cost no more resources at all. It is fantastic for Arduino based project. I2C Address: 0X20~0X27 (the original address is 0X20,you can change it yourself) the backlight and contrast is adjusted by potentiometer Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated cable I2C Address: 0x27 (I2C Address: 0X20~0X27 (the original address is 0X27,you can change it yourself) Specification: Compatible for 1602 LCD Supply voltage: 5V Size: 5.5x2.3x1.4cm Package included: 5 x IIC/I2C/TWI/SPI serial interface module

Electronics/Audio

5Pcs IIC/I2C/TWI/SPI Serial Port Module 5V 1602LCD Display For Arduino

3Pcs IIC/I2C/TWI/SPI Serial Port Module 5V 1602LCD Display For Arduino

3Pcs IIC/I2C/TWI/SPI Serial Port Module 5V 1602LCD Display For Arduino

Description: This is another great IIC/I2C/TWI/SPI Serial Interface. As the pin resources of Arduino controller is limited, your project may be not able to use normal LCD shield after connected with a certain quantity of sensors or SD card. However, with this I2C interface module, you will be able to realize data display via only 2 wires. If you already has I2C devices in your project, this LCD module actually cost no more resources at all. It is fantastic for Arduino based project. I2C Address: 0X20~0X27 (the original address is 0X20,you can change it yourself) the backlight and contrast is adjusted by potentiometer Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated cable I2C Address: 0x27 (I2C Address: 0X20~0X27 (the original address is 0X27,you can change it yourself) Specification: Compatible for 1602 LCD Supply voltage: 5V Size: 5.5x2.3x1.4cm Package included: 3 x IIC/I2C/TWI/SPI serial interface module

Electronics/Audio

3Pcs IIC/I2C/TWI/SPI Serial Port Module 5V 1602LCD Display For Arduino

20Pcs IIC/I2C/TWI/SPI Serial Port Module 5V 1602LCD Display For Arduino

20Pcs IIC/I2C/TWI/SPI Serial Port Module 5V 1602LCD Display For Arduino

Description: This is another great IIC/I2C/TWI/SPI Serial Interface. As the pin resources of Arduino controller is limited, your project may be not able to use normal LCD shield after connected with a certain quantity of sensors or SD card. However, with this I2C interface module, you will be able to realize data display via only 2 wires. If you already has I2C devices in your project, this LCD module actually cost no more resources at all. It is fantastic for Arduino based project. I2C Address: 0X20~0X27 (the original address is 0X20,you can change it yourself) the backlight and contrast is adjusted by potentiometer Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated cable I2C Address: 0x27 (I2C Address: 0X20~0X27 (the original address is 0X27,you can change it yourself) Specification: Compatible for 1602 LCD Supply voltage: 5V Size: 5.5x2.3x1.4cm Package included: 20 x IIC/I2C/TWI/SPI serial interface module

Electronics/Audio

20Pcs IIC/I2C/TWI/SPI Serial Port Module 5V 1602LCD Display For Arduino

CJMCU-PCA9685 16 Channel PWM Servo Control Module 12 Bit Fm I2C

CJMCU-PCA9685 16 Channel PWM Servo Control Module 12 Bit Fm I2C

CJMCU-PCA9685 16 Channel PWM Servo Control Module 12 Bit Fm I2C Feature: - 1MHz Fast-mode Plus compatible owned 30mA high drive capability on SDA of I2C bus interface to drive highly capacitive bus - Each LED output can be achieved from the fully closed (default) to 4096 (12) between the maximum brightness linear programmable brightness - Software programmable open-drain LED output selection (default is push-pull) of 16 push-pull outputs (5V at 25mA sink can absorb and provide 10mA Source Current) no input function - Programmable output state is in response to an order to change or stop in order to achieve all outputs simultaneously update or byte by byte (byte-by-byte) update output (default 'Stop command changes') - Active-low output enable input pin when the pin is high LED outputs can be programmed 0,1 or tri-state (high impedance power-on default) - 6 hardware address pins so that the same I2C devices can be connected to the bus 62 PCA9685 - LED output frequency (all LED) is typically 40Hz to 1000Hz (When the oscillator is 25MHz, the prescaler register default value 1EH will generate refresh rate of 200Hz) - 4 software-programmable I2C bus address (a LED group call (Call) addresses and three LED sub call (Call) address) so that the device can be set in any combination to be addressed at the same time (for example, a register for ' all calls (All Call) 'then all PCA9634 devices on the I2C bus can be addressed at the same time, while the second register for three different addresses, then the device group on a bus device can 1/3 at the same time be addressed) software can enable and disable I2C bus address - Software reset feature (SWRST Call) makes the device via the I2C bus reset - 25MHz internal oscillator requires no external components - The maximum allowable 50MHz external clock input - An internal power-on reset - In the SDA / SCL inputs with noise filter - Output pin has edge generation rate control - No glitches on power output - Hot-Access - Low Standby Current - Operating voltage range: 2.3V to 5.5V

Electronics/Audio

CJMCU-PCA9685 16 Channel PWM Servo Control Module 12 Bit Fm I2C

CJMCU-MCP4725 I2C DAC Breakout Development Board Module

CJMCU-MCP4725 I2C DAC Breakout Development Board Module

CJMCU-MCP4725 I2C DAC Breakout Development Board Module Description: You've always wanted to output analog voltages from a microcontroller, the MCP4725 is the DAC that will let you do it. The CJMCU-MCP4725 is an I2C controlled Digital-to-Analog converter (DAC). A DAC allows you to send analog signal, such as a sine wave, from a digital source, such as the I2C interface on the Arduino microcontroller. Digital to analog converters are great for sound generation, musical instruments, and many other creative projects. This version of the CJMCU-MCP4725 Breakout fixes a few issues with the board including the IC footprint, the I2C pinout, changes the overall board dimensions to better fit your projects, and a few more minor tweaks. This board breaks out each pin you will need to access and use the MCP4725 including GND and Signal OUT pins for connecting to an oscilloscope or any other device you need to hook up to the board. Also on board are SCL, SDA, VCC, and another GND for your basic I2C pinout. Additionally, if you are looking to have more than one MCP4725 on a bus, the pull-up resistors on this board can be disabled just check the Hookup Guide in the Documents section below for instructions and tips on doing this. Feature: 12-bit resolution I2C Interface (Standard, Fast, and High-Speed supported) Small package 2.7V to 5.5V supply Internal EEPROM to store settings Package included: 1 x CJMCU-MCP4725 I2C DAC Breakout Development Board Module

Electronics/Audio

CJMCU-MCP4725 I2C DAC Breakout Development Board Module

3Pcs CJMCU-MCP4725 I2C DAC Breakout Development Board Module

3Pcs CJMCU-MCP4725 I2C DAC Breakout Development Board Module

3Pcs CJMCU-MCP4725 I2C DAC Breakout Development Board Module Description: You've always wanted to output analog voltages from a microcontroller, the MCP4725 is the DAC that will let you do it. The CJMCU-MCP4725 is an I2C controlled Digital-to-Analog converter (DAC). A DAC allows you to send analog signal, such as a sine wave, from a digital source, such as the I2C interface on the Arduino microcontroller. Digital to analog converters are great for sound generation, musical instruments, and many other creative projects. This version of the CJMCU-MCP4725 Breakout fixes a few issues with the board including the IC footprint, the I2C pinout, changes the overall board dimensions to better fit your projects, and a few more minor tweaks. This board breaks out each pin you will need to access and use the MCP4725 including GND and Signal OUT pins for connecting to an oscilloscope or any other device you need to hook up to the board. Also on board are SCL, SDA, VCC, and another GND for your basic I2C pinout. Additionally, if you are looking to have more than one MCP4725 on a bus, the pull-up resistors on this board can be disabled just check the Hookup Guide in the Documents section below for instructions and tips on doing this. Feature: 12-bit resolution I2C Interface (Standard, Fast, and High-Speed supported) Small package 2.7V to 5.5V supply Internal EEPROM to store settings Package included: 3 x CJMCU-MCP4725 I2C DAC Breakout Development Board Module

Electronics/Audio

3Pcs CJMCU-MCP4725 I2C DAC Breakout Development Board Module

5Pcs CJMCU-MCP4725 I2C DAC Breakout Development Board Module

5Pcs CJMCU-MCP4725 I2C DAC Breakout Development Board Module

5Pcs CJMCU-MCP4725 I2C DAC Breakout Development Board Module Description: You've always wanted to output analog voltages from a microcontroller, the MCP4725 is the DAC that will let you do it. The CJMCU-MCP4725 is an I2C controlled Digital-to-Analog converter (DAC). A DAC allows you to send analog signal, such as a sine wave, from a digital source, such as the I2C interface on the Arduino microcontroller. Digital to analog converters are great for sound generation, musical instruments, and many other creative projects. This version of the CJMCU-MCP4725 Breakout fixes a few issues with the board including the IC footprint, the I2C pinout, changes the overall board dimensions to better fit your projects, and a few more minor tweaks. This board breaks out each pin you will need to access and use the MCP4725 including GND and Signal OUT pins for connecting to an oscilloscope or any other device you need to hook up to the board. Also on board are SCL, SDA, VCC, and another GND for your basic I2C pinout. Additionally, if you are looking to have more than one MCP4725 on a bus, the pull-up resistors on this board can be disabled just check the Hookup Guide in the Documents section below for instructions and tips on doing this. Feature: 12-bit resolution I2C Interface (Standard, Fast, and High-Speed supported) Small package 2.7V to 5.5V supply Internal EEPROM to store settings Package included: 5 x CJMCU-MCP4725 I2C DAC Breakout Development Board Module

Electronics/Audio

5Pcs CJMCU-MCP4725 I2C DAC Breakout Development Board Module