Home

UART

433MHz E32-TTL-100 LoRa SX1278/SX1276 433M RF FCC CE UART USART Wireless Transceiver Module

433MHz E32-TTL-100 LoRa SX1278/SX1276 433M RF FCC CE UART USART Wireless Transceiver Module

Features: Model: E32-TTL-100 E32-TTL-100 is a wireless transceiver module based on SX1278 from SEMTECH(can be transmitter and receiver both). It adopts LoRa spread spectrum technology, with this technology the transmitting distance and penetration ability of the module improved more than 1 times compared with traditional FSK. The module features FEC (forward error correction) algorithm, which ensure it's good anti-interference ability. E32-TTL-100 can be compatible with other E32 modules. Specifications: 1. Interface: UART 2. Power: 20dBm 3. Distance: 3000m 4. RF connector: SMA-K 5. Frequency: 433MHz (410-441MHz) 6. Dimension: 24x43mm 7. Slot: SMA Electrical parameter: 1. Frequency band: 410 - 441MHz, default: 433.0MHz, channel:32, 1MHz stepped frequency,Recommending frequency: 4335MHz, 2. Connector: 1*7*2.54mm,plug-in 3. Supply voltage: 2.3 - 5.5V DC (Note: the voltage higher than 5.5V is forbidden.) 4. Communication level: UART, USART 5. Operation range: About 3000m(test condition:clear and open area& maximum power,antenna gain: 5dBi,height:> 2m,air date rate: 2.4Kbps) 6. Transmitting power: Maximum 20dBm(100mW)/ four optional level(0-3),step by 3dBm 7. Air data rate: Default 2.4kbps, can be configured to 0.3,1.2,2.4,4.8,9.6,19.2Kbps 8. Standby current: 2.0uA(mode 3,M1=1,M0=1) 9. Transmitting current: 110mA at 20dBm 10. Receiving current: 14.5mA(mode 0 or mode 1) / minimum 30uA(mode 2 + 2s wake-up time) 11. Communication interface: UART, 8N1,8E1,8O1, eight kinds of UART baud Rate, from 1200 to 115200 bps 12. Driving mode: UART can be configured to push-pull/high pull, open-drain 13. Transmitting length: 512 bytes buffer,58 bytes per package 14. Receiving length: 512 bytes buffer,58 bytes per package 15. Address: 65536 configurable addresses(easy for network, broadcast and fixed transmission) 16. RSSI support: Built-in intelligent processing 17. Sensitivity: -130dbm at 0.3Kbps ( sensitivity has nothing to do with serial baud rate and timing) 18. Antenna type: SMA-K (External thread hole, 50 ohm impedance) 19. Op

Electronics/Audio

433MHz E32-TTL-100 LoRa SX1278/SX1276 433M RF FCC CE UART USART Wireless Transceiver Module

SIIG 2-Port RS232 Serial PCI with 16950 UART - 1 Pack - Plug-in Card - PCI - PC - 2 x Number of Serial Ports External - RoHS Compliance

SIIG 2-Port RS232 Serial PCI with 16950 UART - 1 Pack - Plug-in Card - PCI - PC - 2 x Number of Serial Ports External - RoHS Compliance

SIIG''s 2-Port RS232 Serial PCI with 16950 UART is designed to add two RS232 9-pin serial ports to PCI enabled desktop computers. This 2-port serial adapter card comes with two high-speed 16950 UART DB9 serial ports delivering data transfer rates of up to 920Kb/s. It supports IRQ sharing to reduce IRQ conflicts, PME (Power Management Event) that allows device to request a change in system power state (wake up system), and features built-in 128-byte FIFO buffers to dramatically increase data transmit and receive speeds especially under Windows multitasking environment. The 2-Port RS232 Serial PCI with 16950 UART can be installed in 32-/64-bit, 3.3v/5v PCI and PCI-X slots. It is the fast and reliable solution to connect a wide variety of serial port devices such as 56K V.90 external modems, ISDN terminal adapters, PDAs, digital cameras, label printers and more.SIIG''s 2-Port RS232 Serial PCI with 16950 UART is FCC and CE regulatory approved and is RoHS compliant. It is fully compatible with a wide variety of Windows operating systems and is backed by SIIG''s limited 2-year warranty.

Business/Services/Hardware

SIIG 2-Port RS232 Serial PCI with 16950 UART - 1 Pack - Plug-in Card - PCI - PC - 2 x Number of Serial Ports External - RoHS Compliance

Holybro Kakute F4 V2 STM32F405 Flight Controller With Betaflight OSD for RC Multirotor FPV Racing Drone

Holybro Kakute F4 V2 STM32F405 Flight Controller With Betaflight OSD for RC Multirotor FPV Racing Drone

Holybro Kakute F4 V2 STM32F405 Flight Controller With Betaflight OSD for RC Multirotor FPV Racing Drone Description: The Holybro Kakute F4 flight controller supports important features of Betaflight/Cleanflight, such as OSD and Dshot. The faster F4 processor gives room for future feature development: run all features at the fast 8 kHz PID loop rate, at single-digit CPU utilization. Because of issues with serial inversion, other F4 boards struggle to support protocols such as FrSky SBUS and SmartPort at the same time. The Kakute F4 is designed to support all serial protocols at once. Specification (user manual): MCU: STM32F405RGT6 32-bit processor IMU: ICM20689 (SPI) Barometer: BMP280 USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART) 5 hardware UARTS (UART1,3,4, 5, 6) Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported. 128 Mbit Dataflash chip for Blackbox logging Dimensions: 35x30x8mm (includes USB in height) Mounting Holes: Standard 30.5mm square to center of holes Weight: 7g New V2 Features: -Additional UART (UART 4) added to support serial camera communication such as to RunCam Split. Please note this is NOT the same as Betaflight Camera Control feature, which controls the menu of FPV cameras like Swift, etc. -Additional UART (UART 5) added to support ESC telemetry such as from BLHeli_32 and KISS. -Through-hole solder pads instead of flat pads for more secure soldering especially for beginners. -Barometer sensor on board allows altitude hold mode. -I2C pad available for certain external sensors. Features: -Supports Betaflight and Cleanflight. -Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles. -Soft-mounting built in. The IMU ('gyro') chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself. -New high-performance / low-noise / high sensitivity IMU.

Toys/Games/Electronic

Holybro Kakute F4 V2 STM32F405 Flight Controller With Betaflight OSD for RC Multirotor FPV Racing Drone

Holybro Kakute F4 AIO All in One V2 Flight Controller + Tekko32 35A BLHeli_32 ESC Dshot1200 2-6S

Holybro Kakute F4 AIO All in One V2 Flight Controller + Tekko32 35A BLHeli_32 ESC Dshot1200 2-6S

Holybro Kakute F4 AIO All in One V2 Flight Controller + Tekko32 35A BLHeli_32 ESC Dshot1200 2-6S Items Descriptions Features Holybro Kakute F4 AIO All in One V2 Item name: F4 AIO V2 Flight Controller MCU: STM32F405RGT6 32-bit processor IMU: ICM20689 (SPI) Barometer: BMP280 USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART) 5 hardware UARTS (UART1, 3, 4, 5, 6) Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported. 128 Mbit Dataflash chip for Blackbox logging Dimensions: 35x43x7mm (includes USB in height) Mounting Holes: Standard 30.5mm square to center of holes Weight: 7g Additional UART (UART 4) added to support serial camera communication such as to RunCam Split. Additional UART (UART 5) added to support ESC telemetry such as from BLHeli_32 and KISS. Through-hole solder pads instead of flat pads for more secure soldering especially for beginners. Barometer sensor on board allows altitude hold mode. I2C pad available for certain external sensors. Supports Betaflight and Cleanflight. Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles. Soft-mounting built in. The IMU ('gyro') chip on this board is mounted on vibration-isolating foam. New high-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz. 2 oz. copper PCB allows up to 120A maximum continuous current. Dedicated bootloader button for easy firmware flashing. Low-profile design fits into even very compact frames. Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on 'B+' pad only). Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F4 AIO monitors voltage directly from the battery power lead. Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 1.5 amps and 3.3v at up to 200 mA to power p

Toys/Games/Electronic

Holybro Kakute F4 AIO All in One V2 Flight Controller + Tekko32 35A BLHeli_32 ESC Dshot1200 2-6S

Holybro Kakute F4 AIO V2 Flight Controller PDB OSD+Atlatl HV V2 5.8G 40CH FPV Transmitter for RC Drone

Holybro Kakute F4 AIO V2 Flight Controller PDB OSD+Atlatl HV V2 5.8G 40CH FPV Transmitter for RC Drone

Holybro Kakute F4 AIO V2 Flight Controller PDB OSD+Holybro Atlatl HV V2 5.8G 40CH FPV Transmitter Holybro Kakute F4 AIO V2(user munual): Brand name: Holybro Item name: F4 AIO V2 Flight Controller MCU: STM32F405RGT6 32-bit processor IMU: ICM20689 (SPI) Barometer: BMP280 USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART) 5 hardware UARTS (UART1, 3, 4, 5, 6) Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported. 128 Mbit Dataflash chip for Blackbox logging Dimensions: 35x43x7mm (includes USB in height) Mounting Holes: Standard 30.5mm square to center of holes Weight: 7g Features: -Additional UART (UART 4) added to support serial camera communication such as to RunCam Split. Please note this is NOT the same as Betaflight Camera Control feature, which controls the menu of FPV cameras like Swift, Monster, etc. -Additional UART (UART 5) added to support ESC telemetry such as from BLHeli_32 and KISS. -Through-hole solder pads instead of flat pads for more secure soldering especially for beginners. -Barometer sensor on board allows altitude hold mode. -I2C pad available for certain external sensors. -Supports Betaflight and Cleanflight. -Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles. -Soft-mounting built in. The IMU ('gyro') chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself. -New high-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz. -2 oz. copper PCB allows up to 120A maximum continuous current. -Dedicated bootloader button for easy firmware flashing. -Low-profile design fits into even very compact frames. -Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on 'B+' pad only). -Automatic voltage monitoring. No need to run a separate vBat wire for voltage

Toys/Games/Electronic

Holybro Kakute F4 AIO V2 Flight Controller PDB OSD+Atlatl HV V2 5.8G 40CH FPV Transmitter for RC Drone

Holybro Kakute F4 AIO All in One V2 Flight Controller STM32 F405 MCU Integrated PDB OSD for RC Drone

Holybro Kakute F4 AIO All in One V2 Flight Controller STM32 F405 MCU Integrated PDB OSD for RC Drone

Holybro Kakute F4 AIO All in One V2 Flight Controller STM32 F405 MCU Integrated PDB OSD for RC Drone FPV Racing Multi Rotor The Holybro Kakute F4 AIO All-In-One flight controller makes it easy to build your multirotor. It integrates flight controller (FC) power distribution board (PDB) and on-screen display (OSD) in one. The Kakute F4 AIO V2's layout makes it easy to wire up the other components of the multirotor while keeping the build neat and tidy. Description: Brand name: Holybro Item name: F4 AIO V2 Flight Controller MCU: STM32F405RGT6 32-bit processor IMU: ICM20689 (SPI) Barometer: BMP280 USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART) 5 hardware UARTS (UART1, 3, 4, 5, 6) Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported. 128 Mbit Dataflash chip for Blackbox logging Dimensions: 35x43x7mm (includes USB in height) Mounting Holes: Standard 30.5mm square to center of holes Weight: 7g Features: Additional UART (UART 4) added to support serial camera communication such as to RunCam Split. Please note this is NOT the same as Betaflight Camera Control feature, which controls the menu of FPV cameras like Swift, Monster, etc. Additional UART (UART 5) added to support ESC telemetry such as from BLHeli_32 and KISS. Through-hole solder pads instead of flat pads for more secure soldering especially for beginners. Barometer sensor on board allows altitude hold mode. I2C pad available for certain external sensors. Supports Betaflight and Cleanflight. Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles. Soft-mounting built in. The IMU ('gyro') chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself. New high-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz. 2 oz. copper PCB allows up to 120A

Toys/Games/Electronic

Holybro Kakute F4 AIO All in One V2 Flight Controller STM32 F405 MCU Integrated PDB OSD for RC Drone

Holybro Kakute F4 AIO V2 FC OSD + Atlatl HV 5.8G 40CH Raceband FPV VTX + Tekko32 35A BLHeli_32 ESC

Holybro Kakute F4 AIO V2 FC OSD + Atlatl HV 5.8G 40CH Raceband FPV VTX + Tekko32 35A BLHeli_32 ESC

Holybro Kakute F4 AIO V2 Flight Controller OSD + Atlatl HV 5.8G 40CH Raceband FPV VTX + Tekko32 35A BLHeli_32 ESC Dshot1200 2-6S Items Descriptions Features Holybro Atlatl HV 5.8G 40CH Raceband VTX Transmitting Output Power: 15mW ( Pit Mode) 25mW/ 100mW/ 200mW/ 400mW/ 600mW Switchable Audio: 6 MHz + 6.5 MHz Mono Antenna Connector: MMCX Input Voltage: 7-24V (2-6S Lipo) Dimension: 35(L)x 35(W)x 7(H)mm Mounting Hole: 30.5x30.5mm Weight: 10.8g Compatible with all major FPV receivers from vendors such as Fatshark, ImmersionRC, etc. Supports the standard 40-channel set: band A, B, E, Fatshark, and Raceband. Telemetry input allows remote control by the flight controller (where supported). Change channel, transmit power, and more from Betaflight OSD, flight controller USB port, Taranis, and more. Variable transmit power from 25 mW to 600 mW. Use 25 mW for a race and then easily switch to 600 mW for freestyle. Pit Mode allows you to power up safely without the risk of knocking other pilots out of the air. Mono audio input allows you to install a microphone, so you can listen to your motors while you fly, no matter how far away you fly. Standard 36mm form factor allows you to mount the Atlatl directly in your flight controller stack. Holybro Kakute F4 AIO All in One V2 Item name: F4 AIO V2 Flight Controller MCU: STM32F405RGT6 32-bit processor IMU: ICM20689 (SPI) Barometer: BMP280 USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART) 5 hardware UARTS (UART1, 3, 4, 5, 6) Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported. 128 Mbit Dataflash chip for Blackbox logging Dimensions: 35x43x7mm (includes USB in height) Mounting Holes: Standard 30.5mm square to center of holes Weight: 7g Additional UART (UART 4) added to support serial camera communication such as to RunCam Split. Additional UART (UART 5) added to support ESC telemetry such as from BLHeli_32 and KISS. Through-hole solder pads instead of flat pads for more secure soldering especially for b

Toys/Games/Electronic

Holybro Kakute F4 AIO V2 FC OSD + Atlatl HV 5.8G 40CH Raceband FPV VTX + Tekko32 35A BLHeli_32 ESC

SIIG DP 1-Port RS232 Serial PCI with 16550 UART - 1 Pack - PCI - 1 x Number of Serial Ports External - RoHS Compliance

SIIG DP 1-Port RS232 Serial PCI with 16550 UART - 1 Pack - PCI - 1 x Number of Serial Ports External - RoHS Compliance

SIIG''s DP 1-Port RS232 Serial PCI with 16550 UART adapter card is designed to add one 9-pin RS232 serial to your PCI enabled desktop computer. This serial adapter comes with one high-speed 16550 UART serial ports with 256-byte FIFO buffer to deliver data transfer rates up to 230Kb/s. The dual profile design, along with the included spare low-profile bracket, allows you to install the board into either standard height or low profile system chassis. The DP 1-Port RS232 Serial PCI with 16550 UART is the smart and cost effective solution to add one RS232 serial port for additional serial port device connections.The DP 1-Port RS232 Serial PCI with 16550 UART is fully compliant with PCI Local Bus Specification, Revision 2.3, is FCC and CE approved, and RoHS compliant. It is fully compatible with a wide variety of Windows operating systems and is backed by SIIG''s limited 2-year warranty.

Business/Services/Hardware

SIIG DP 1-Port RS232 Serial PCI with 16550 UART - 1 Pack - PCI - 1 x Number of Serial Ports External - RoHS Compliance

SIIG 1S1P Mini PCIe with 16950 UART - 1 x 9-pin DB-9 RS-232 Serial, 1 x 25-pin DB-25 IEEE 1284 Parallel Mini PCI Express - 1 Pack - RoHS Compliance

SIIG 1S1P Mini PCIe with 16950 UART - 1 x 9-pin DB-9 RS-232 Serial, 1 x 25-pin DB-25 IEEE 1284 Parallel Mini PCI Express - 1 Pack - RoHS Compliance

SIIG''s 1S1P Mini PCIe with 16950 UART is designed to add one 9-pin RS232 serial port and one DB25 parallel port to your PCIe-enabled desktop computer. It features one high speed 16950 UART serial port supporting up to 460 Kb/s with deep 128-byte FIFO per transmitter & receiver and one parallel port supporting ECP, EPP and SPP parallel port modes. It can be installed in any available Mini PCI Express slot and is the perfect solution enabling you to connect a wide variety of serial and parallel devices to your desktop computer.The 1S1P Mini PCIe with 16950 UART is compliant with PCI Express Base Specification, FCC & CE regulatory approved and RoHS-compliant. It is also fully compatible with a wide variety of Windows operating systems and backed by SIIG''s limited 2-year warranty.

Business/Services/Hardware

SIIG 1S1P Mini PCIe with 16950 UART - 1 x 9-pin DB-9 RS-232 Serial, 1 x 25-pin DB-25 IEEE 1284 Parallel Mini PCI Express - 1 Pack - RoHS Compliance

SIIG 4-port PCI Serial Adapter - 1 Pack - PCI - 4 x Number of Serial Ports External - RoHS Compliance

SIIG 4-port PCI Serial Adapter - 1 Pack - PCI - 4 x Number of Serial Ports External - RoHS Compliance

SIIG''s 4-Port RS232 Serial PCI with 16550 UART adapter card is designed to add four 9-pin RS232 serial ports to your PIC enabled desktop computer. This serial adapter comes with four high-speed 16550 UART serial ports with 256-byte FIFO buffer to deliver data transfer rates up to 230Kb/s. The 4-Port RS232 Serial PCI with 16550 UART is the smart and cost effective solution to add 4 RS232 serial ports for additional serial port device connections.The 4-Port RS232 Serial PCI with 16550 UART is fully compliant with PCI Local Bus Specification, Revision 2.3, is FCC, and CE approved, and RoHS-compliant. It is fully compatible with a wide variety of Windows operating systems and is backed by SIIG''s limited 2-year warranty.

Business/Services/Hardware

SIIG 4-port PCI Serial Adapter - 1 Pack - PCI - 4 x Number of Serial Ports External - RoHS Compliance